0
Dear yassinov and equally respected associates,
First, thanks for your reading my post.
I've never though I would finish here, beeing in the technical profession as well, but look like experience is something that you cannot substitute in some specific area.
No need need to say that they shall be a donation whether it can be solved here or either send to get it repair. I'd be very grateful of any hint that shed the light on this issue.
Problem data:
- device type : DM800HD PVR (DM800pro)
- authenticity : clone
- sim version: 2.01
- boot loader : a little confused :
1/in the very first image, telenetting "ipkg list" would give dreambox second bootloader 76 r1, however if I keep the on/ff button pressed when connecting the supply, I see second bootloader 82 (the mode allowing to uploading a new image through http)
2/I successfully applied the image: Sat4fun-Dreamelite-BlackHole_PHOENIX_DM800HD-SIM2-SSL84.nfi then ssl becomes 84.
nb: Actually, the problem occured when trying to upload the image: "OoZooN-Image-dm800-3.2.1.nfi"
-> I've done the following:
- making sure to use real DB9 (no usb) cable or cross-over on windows XP station (not mobile). I've made my own DB9 cable based on straight rs232 cable reshuffled into
1,9: not connected
2->3
3->2
5->5
4->6
6->4
7->8
8->7
(and checked with a multimeter)
I've used from the old dreamup software for DM500 up to the patched dreamup of 2009 from forhike and natas.
whether using cross over cable (tested ) with the right device config on XP or serial connection @ switching on just after pressing connect or 15s after pressing connect according to other versions nothing happened.
I've used basically all software of the Dreamoem toolbox v9 including all of yassinov included in this compilation, nothing happened.
I've ordered a new DB9 cable, as of today I hope it's only a cable problem.
again, I'd be very grateful of any hint that shed the light on this issue.
BEst regards, Tareeq
First, thanks for your reading my post.
I've never though I would finish here, beeing in the technical profession as well, but look like experience is something that you cannot substitute in some specific area.
No need need to say that they shall be a donation whether it can be solved here or either send to get it repair. I'd be very grateful of any hint that shed the light on this issue.
Problem data:
- device type : DM800HD PVR (DM800pro)
- authenticity : clone
- sim version: 2.01
- boot loader : a little confused :
1/in the very first image, telenetting "ipkg list" would give dreambox second bootloader 76 r1, however if I keep the on/ff button pressed when connecting the supply, I see second bootloader 82 (the mode allowing to uploading a new image through http)
2/I successfully applied the image: Sat4fun-Dreamelite-BlackHole_PHOENIX_DM800HD-SIM2-SSL84.nfi then ssl becomes 84.
nb: Actually, the problem occured when trying to upload the image: "OoZooN-Image-dm800-3.2.1.nfi"
-> I've done the following:
- making sure to use real DB9 (no usb) cable or cross-over on windows XP station (not mobile). I've made my own DB9 cable based on straight rs232 cable reshuffled into
1,9: not connected
2->3
3->2
5->5
4->6
6->4
7->8
8->7
(and checked with a multimeter)
I've used from the old dreamup software for DM500 up to the patched dreamup of 2009 from forhike and natas.
whether using cross over cable (tested ) with the right device config on XP or serial connection @ switching on just after pressing connect or 15s after pressing connect according to other versions nothing happened.
I've used basically all software of the Dreamoem toolbox v9 including all of yassinov included in this compilation, nothing happened.
I've ordered a new DB9 cable, as of today I hope it's only a cable problem.
again, I'd be very grateful of any hint that shed the light on this issue.
BEst regards, Tareeq
