0
OK thanks for showing how to use hyper terminal, but now that I know how to use it what am I supposed to do with it and once I have done it how can I send it to you? You mentioned a logo? Do you mean the boot log that appears on hyperterminal? I can send it to you right now as I had it right at the beginning, I got it using Putty which is much easier to use. The problem is how do I attach a file or a screen dump to these forum messages?
Here is he booting log. It gets up to "NO CA FOUND" and it stops. I then press X and it carries on up to "libpagecache exists... drop caches now!" where it keeps printing the same thing and it doesn't go any further.
Can this help you to work out what is going wrong?
Many thanks again
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.07.02 17:18:40 =~=~=~=~=~=~=~=~=~=~=~=
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=FFFFFFE4
RC2=00000015
WC2=00000036
RC3=0000000D
WC3=FFFFFFE4
RC4=0000000D
WC4=00000036
NWC=0000000D
RC5=00000005
WC5=0000000D
RC6=00000014
WC6=0000000D
NRC=0000000C
RW=00000010
WW=00000053
G=00000000 R=0000000C W=0000000D
BL=00000000
RC1=00000002
RC2=00000011
BL=00000001
RC1=00000002
RC2=00000014
BL=00000002
RC1=00000003
RC2=00000014
BL=00000003
RC1=00000007
RC2=00000014
BL=00000004
RC1=00000001
RC2=00000011
BL=00000005
RC1=00000005
RC2=00000015
BL=00000006
RC1=00000002
RC2=00000012
BL=00000007
RC1=00000005
RC2=00000014
3
COPY CODE
COMPARE CODE
4567
© 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox D M500HD
FIRST STAGE 1.2/400 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-01)
....
0.007 - BCM board setup
0.007 - fp init
0.007 - ca init
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
CA invalid
NO CONFIGURATION DATA PRESENT. STOP.
lcd: * ERR01: NO CA FOUND
******************************
I then press X and it carries on with the below information
*****************************
3.369 - load config
3.396 - config loaded.
* woke up from power
* press [S] to enter setup
3.397 - ide init
lcd: BOOT #84
P23 detected!
3.498 - main control
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000:
USB Hub
- read config file: /boot/secondstage.conf
3.530 - load /boot/secondstage.conf to 833000c0 (max=65535)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++UUUUUUUUUUUUUUUUUUUU
4.479 - jffs2 size: 3520 kb
4.480 - network: 4.480 dhcp
4.493 - starting network
4.497 - httpd, telnetd, dreamupd
dreamupd initialized
4.498 - ok. start receiving packets
4.499 - using jffs2
Scanning JFFS2 FS: . | / - \ | / - \ | / - \ | done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
4.596 - size: 0
- failed to open /boot/secondstage.conf
4.597 - not entering setup
4.597 - execute script: /cf/autorun.bat
4.598 - load /cf/autorun.bat to 833000c0 (max=65535)
4.598 - size: -1
- failed to open /cf/autorun.bat
4.599 - force boot: -1
4.599 - try boot from 1:
4.599 - execute script: /boot/autoexec.bat
4.600 - load /boot/autoexec.bat to 833000c0 (max=65535)
4.600 - using jffs2
4.601 - size: 163
lcd: /boot/bootlogo-dm500hd.elf.gz
4.603 - load /boot/bootlogo-dm500hd.elf.gz to 82000000 (max=16777216)
4.603 - using jffs2
4.619 - size: 242111
4.619 - decompressing elf (compressed: 242111 bytes)
4.674 - decompression ok (uncompressed: 563324 bytes)
4.674 - loading elf image at 88000000
4.780 - jumping to 8044fdb0
4.781 - load /boot/bootlogo-dm500hd.jpg to a2800000 (max=1048576)
4.781 - using jffs2
4.839 - size: 477509
bootlogo size: 477509
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright © 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-3.2-dm500hd.gz
5.810 - load /boot/vmlinux-3.2-dm500hd.gz to 82000000 (max=16777216)
5.810 - using jffs2
5.886 - size: 2822958
5.886 - decompressing elf (compressed: 2822958 bytes)
6.515 - decompression ok (uncompressed: 6039932 bytes)
6.516 - loading elf image at 88000000
6.939 * Quiesce...
6.939 *** Turning off USB
USB: Unregistering Hub VID 0x0000 PID 0x0000
USB: Powering down bus 0 port 2
USB: Powering down bus 0 port 1
6.940 *** Quiesce network...
6.941 - jumping to 80481550
[ 0.000000] Linux version 3.2-dm500hd (dreameli@oe) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Wed Jan 16 09:14:13 UTC 2013
[ 0.000000] Fetching vars from bootloader...
[ 0.000000] Early serial console at MMIO32 0x10400b00 (options '1000000n8')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
[ 0.000000] Using 256 MB RAM (from straps)
[ 0.000000] Fetch var 'memsize' = '140'
[ 0.000000] CPU revision is: 0002a044 (Brcm4380)
[ 0.000000] FPU revision is: 00130001
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] bmem: adding 134 MB LINUX region at 5 MB (0x0861f000@0x005e1000)
[ 0.000000] bmem: adding 116 MB RESERVED region at 140 MB (0x07400000@0x08c00000)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00010000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00010000
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat 8058a400, node_mem_map 81000000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5440 r8192 d15040 u32768
[ 0.000000] pcpu-alloc: s5440 r8192 d15040 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=ttyS0,115200 debug bmem=116M@140M
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.000000] Memory: 135016k/262144k available (4670k kernel code, 127128k reserved, 1004k data, 220k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Measuring MIPS counter frequency...
[ 0.000000] Detected MIPS clock frequency: 405 MHz (202.507 MHz counter)
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Calibrating delay loop... 401.40 BogoMIPS (lpj=200704)
[ 0.011000] pid_max: default: 32768 minimum: 301
[ 0.012000] Mount-cache hash table entries: 512
[ 0.014000] SMP: Booting CPU1...
[ 0.015000] CPU revision is: 0002a044 (Brcm4380)
[ 0.015000] FPU revision is: 00130001
[ 0.015000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.015000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.026000] SMP: CPU1 is running
[ 0.026000] Brought up 2 CPUs
[ 0.027000] devtmpfs: initialized
[ 0.031000] NET: Registered protocol family 16
[ 0.033000] PCI2.3->SDRAM window: 512 MB
[ 0.040000] bio: create slab <bio-0> at 0
[ 0.041000] SCSI subsystem initialized
[ 0.042000] libata version 3.00 loaded.
[ 0.042000] usbcore: registered new interface driver usbfs
[ 0.043000] usbcore: registered new interface driver hub
[ 0.043000] usbcore: registered new device driver usb
[ 0.044000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.045000] pci 0000:01:00.0: [14e4:8602] type 0 class 0x000101
[ 0.046000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
[ 0.046000] pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
[ 0.047000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
[ 0.048000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
[ 0.049000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff])
[ 0.050000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
[ 0.051000] Switching to clocksource upg
[ 0.063000] NET: Registered protocol family 2
[ 0.064000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.065000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.067000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.068000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.069000] TCP reno registered
[ 0.069000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.070000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.071000] NET: Registered protocol family 1
[ 0.072000] RPC: Registered named UNIX socket transport module.
[ 0.073000] RPC: Registered udp transport module.
[ 0.074000] RPC: Registered tcp transport module.
[ 0.074000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.075000] PCI: CLS 0 bytes, default 64
[ 0.078000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.080000] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.081000] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[ 0.084000] msgmni has been set to 263
[ 0.085000] io scheduler noop registered
[ 0.086000] io scheduler cfq registered (default)
[ 0.087000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
ÿ[ 0.109000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
[ 0.110000] console [ttyS0] enabled, bootconsole disabled
[ 0.110000] console [ttyS0] enabled, bootconsole disabled
[ 0.132000] serial8250.0: ttyS1 at MMIO 0x10400b80 (irq = 67) is a 16550A
[ 0.138000] loop: module loaded
[ 0.139000] sata_brcmstb 0000:01:00.0: version 4.0
[ 0.139000] brcm-pm: enabling sata clocks
[ 0.140000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
[ 0.140000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 0.338000] scsi0 : sata_brcmstb
[ 0.339000] scsi1 : sata_brcmstb
[ 0.340000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
[ 0.341000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
[ 0.343000] Broadcom STB NAND controller (BrcmNand Controller)
[ 0.344000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0
[ 0.347000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:ba:da:80)
[ 0.348000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.349000] brcm-pm: enabling usb clocks
[ 0.349000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.350000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 0.382000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
[ 0.388000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 0.389000] hub 1-0:1.0: USB hub found
[ 0.390000] hub 1-0:1.0: 2 ports detected
[ 0.390000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[ 0.391000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
[ 0.423000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
[ 0.429000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[ 0.430000] hub 2-0:1.0: USB hub found
[ 0.430000] hub 2-0:1.0: 2 ports detected
[ 0.431000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.432000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 0.433000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
[ 0.434000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
[ 0.499000] hub 3-0:1.0: USB hub found
[ 0.500000] hub 3-0:1.0: 2 ports detected
[ 0.501000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[ 0.501000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
[ 0.502000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
[ 0.568000] hub 4-0:1.0: USB hub found
[ 0.569000] hub 4-0:1.0: 2 ports detected
[ 0.570000] Initializing USB Mass Storage driver...
[ 0.570000] usbcore: registered new interface driver usb-storage
[ 0.571000] USB Mass Storage support registered.
[ 0.572000] i2c /dev entries driver
[ 0.572000] ALSA device list:
[ 0.573000] No soundcards found.
[ 0.573000] TCP cubic registered
[ 0.574000] NET: Registered protocol family 17
[ 0.574000] Registering the dns_resolver key type
[ 0.575000] EBI CS1: setting up NAND flash (primary)
[ 0.576000] mtd->oobsize=0, mtd->eccOobSize=0
[ 0.577000] NAND_CS_NAND_XOR=00000000
[ 0.577000] B4: NandSelect=40000202, nandConfig=04042300, chipSelect=1
[ 0.578000] brcmnand_read_id: CS1: dev_id=ad76ad76
[ 0.579000] After: NandSelect=40000202, nandConfig=04042300
[ 0.579000] Block size=00004000, erase shift=14
[ 0.580000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
[ 0.581000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[ 0.582000] timing1 not adjusted: 5363444f
[ 0.582000] timing2 not adjusted: 00000fc6
[ 0.583000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB on CS1
[ 0.583000]
[ 0.583000] Found NAND on CS1: ACC=f7ff1010, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
[ 0.585000] BrcmNAND version = 0x0302 64MB @00000000
[ 0.585000] B4: NandSelect=40000202, nandConfig=04042300, chipSelect=1
[ 0.586000] brcmnand_read_id: CS1: dev_id=ad76ad76
[ 0.587000] After: NandSelect=40000202, nandConfig=04042300
[ 0.587000] Found NAND flash on Chip Select 1, chipSize=64MB, usable size=64MB, base=0
[ 0.588000] brcmnand_scan: B4 nand_select = 40000202
[ 0.589000] brcmnand_scan: After nand_select = 40000202
[ 0.590000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
[ 0.590000] Brcm NAND controller version = 3.2 NAND flash size 64MB @1c000000
[ 0.591000] brcmnand_scan: mtd->oobsize=16
[ 0.592000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[ 0.593000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
[ 0.594000] -->brcmnand_default_bbt
[ 0.594000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[ 0.595000] Bad block table Bbt0 found at page 0001ffe0, version 0x01 for chip on CS1
[ 0.596000] Bad block table 1tbB found at page 0001ffc0, version 0x01 for chip on CS1
[ 0.597000] brcmnandCET: Status -> Deferred
[ 0.598000] Adjust partition complete size from 4000000 to 3f00000 to avoid overlap with BBT reserved space
[ 0.599000] Adjust partition root partition size from 3c00000 to 3b00000 to avoid overlap with BBT reserved space
[ 0.600000] Creating 4 MTD partitions on "brcmnand.0":
[ 0.601000] 0x000000000000-0x000003f00000 : "complete"
[ 0.607000] 0x000000000000-0x000000040000 : "loader"
[ 0.608000] 0x000000040000-0x000000400000 : "boot partition"
[ 0.611000] 0x000000400000-0x000003f00000 : "root partition"
[ 0.672000] ata1: SATA link down (SStatus 4 SControl 300)
[ 0.998000] ata2: SATA link down (SStatus 4 SControl 300)
[ 9.383000] Empty flash at 0x03553d0c ends at 0x03553e00
[ 9.564000] VFS: Mounted root (jffs2 filesystem) on device 31:3.
[ 9.567000] devtmpfs: mounted
[ 9.568000] Freeing unused kernel memory: 220k freed
INIT: version 2.88 booting
Displaying bootlogo.
Mounting squashfs images:loop mounting /squashfs-images/dreambox-dvb-modules-sqsh-img to /media/squashfs-images/dreambox-dvb-modules-sqsh-img
loop mounting /squashfs-images/qt4-embedded-core-sqsh-img to /media/squashfs-images/qt4-embedded-core-sqsh-img
loop mounting /squashfs-images/qt4-embedded-webkit-sqsh-img to /media/squashfs-images/qt4-embedded-webkit-sqsh-img
loop mounting /squashfs-images/sambaserver-sqsh-img to /media/squashfs-images/sambaserver-sqsh-img
loop mounting /squashfs-images/ubuntu-font-family-sqsh-img to /media/squashfs-images/ubuntu-font-family-sqsh-img
Starting udev
[ 13.964000] udevd[120]: starting version 182
udevd[120]: specified group 'pcscd' unknown
[ 14.606000] stb_core: module license 'Proprietary' taints kernel.
[ 14.607000] Disabling lock debugging due to kernel taint
[ 17.340000] enter base init, xvd 20100413, vdc 20100413, rap 20100719, xpt 20100825
[ 17.353000] 17:352999113 SMCA: controller reset timed out
[ 18.549000] tpm: could not read config area!
[ 18.550000] ------------[ cut here ]------------
[ 18.551000] WARNING: at fs/proc/generic.c:808 remove_proc_entry+0x260/0x2b8()
[ 18.551000] name 'serial'
[ 18.552000] Modules linked in: bcm7405(P+) bcm4506(P) lnb_ctrl(P) snd_pcm snd_timer snd_page_alloc tmp100(P) helper(O) cxd1981(P) stb_core(P)
[ 18.553000] Call Trace:
[ 18.554000] [<80488364>] dump_stack+0x8/0x34
[ 18.554000] [<8002e11c>] warn_slowpath_common+0x78/0xa4
[ 18.555000] [<8002e1d0>] warn_slowpath_fmt+0x2c/0x38
[ 18.555000] [<8010e914>] remove_proc_entry+0x260/0x2b8
[ 18.556000] [<c06fe5b4>] tpm_lock+0x70/0x168 [bcm7405]
[ 18.557000]
[ 18.557000] ---[ end trace 00c8ee81ab808208 ]---
[ 18.558000] ------------[ cut here ]------------
[ 18.559000] WARNING: at fs/proc/generic.c:808 remove_proc_entry+0x260/0x2b8()
[ 18.559000] name '0'
[ 18.560000] Modules linked in: bcm7405(P+) bcm4506(P) lnb_ctrl(P) snd_pcm snd_timer snd_page_alloc tmp100(P) helper(O) cxd1981(P) stb_core(P)
[ 18.561000] Call Trace:
[ 18.562000] [<80488364>] dump_stack+0x8/0x34
[ 18.562000] [<8002e11c>] warn_slowpath_common+0x78/0xa4
[ 18.563000] [<8002e1d0>] warn_slowpath_fmt+0x2c/0x38
[ 18.563000] [<8010e914>] remove_proc_entry+0x260/0x2b8
[ 18.564000] [<c024213c>] stb_proc_remove_child+0x60/0x70 [stb_core]
[ 18.565000] [<c06fe5cc>] tpm_lock+0x88/0x168 [bcm7405]
[ 18.566000]
[ 18.567000] ---[ end trace 00c8ee81ab808209 ]---
[ 18.577000] register adapter
[ 18.578000] register adapter
[ 18.579000] register adapter
[ 18.580000] register adapter
[ 18.581000] CPU 0 Unable to handle kernel paging request at virtual address 0000012c, epc == c06fd710, ra == c0a6bba0
[ 18.583000] Oops[#1]:
[ 18.583000] Cpu 0
[ 18.583000] $ 0 : 00000000 10008700 c06fd710 00000001
[ 18.584000] $ 4 : 00000000 00000002 00000000 8039e87c
[ 18.585000] $ 8 : 87eba540 00000003 00000001 802ae190
[ 18.585000] $12 : 00000001 ffffffff 877450e0 00000050
[ 18.586000] $16 : 87fe0000 c0a20000 00000000 00000000
[ 18.587000] $20 : 00000000 80570000 c0a18c50 00000124
[ 18.587000] $24 : 00000018 00000000
[ 18.588000] $28 : 88a2a000 88a2b858 800675d8 c0a6bba0
[ 18.589000] Hi : 00000000
[ 18.589000] Lo : 00000000
[ 18.590000] epc : c06fd710 tpm_ca_find_tag+0x0/0x8c [bcm7405]
[ 18.590000] Tainted: P W O
[ 18.591000] ra : c0a6bba0 init_module+0xba0/0xfe4 [bcm7405]
[ 18.592000] Status: 10008703 KERNEL EXL IE
[ 18.592000] Cause : 00800008
[ 18.593000] BadVA : 0000012c
[ 18.593000] PrId : 0002a044 (Brcm4380)
[ 18.593000] Modules linked in: bcm7405(P+) bcm4506(P) lnb_ctrl(P) snd_pcm snd_timer snd_page_alloc tmp100(P) helper(O) cxd1981(P) stb_core(P)
[ 18.595000] Process modprobe (pid: 137, threadinfo=88a2a000, task=88a25658, tls=771b1490)
[ 18.596000] Stack : 3211b6b8 0132b53d 0132b53d 0132b66f 0132b6d9 3220a440 00000010 8005f9c0
[ 18.597000] 00000000 00000000 00000001 812034a0 00000000 7fffffff 00000003 8005324c
[ 18.598000] 00000108 0cf12014 ff7c0028 01000000 88261ae4 00000800 01000000 00000800
[ 18.599000] 3220a440 00000010 32117e26 00000010 32117e26 00000010 32117e26 32117e26
[ 18.600000] 00000010 812034d8 32117e26 00000010 805671b4 8056a7e0 805ce740 80560000
[ 18.601000] ...
[ 18.602000] Call Trace:
[ 18.602000] [<c06fd710>] tpm_ca_find_tag+0x0/0x8c [bcm7405]
[ 18.603000] [<c0a6bba0>] init_module+0xba0/0xfe4 [bcm7405]
[ 18.604000] [<80001570>] do_one_initcall+0x160/0x1f0
[ 18.605000] [<80069acc>] sys_init_module+0x1044/0x1e28
[ 18.606000] [<8000c5dc>] stack_done+0x20/0x40
[ 18.606000]
[ 18.606000]
[ 18.606000] Code: 03e00008 00000000 00000000 <8c82012c> 00021042 30420001 10400018 00000000 90870133
[ 18.608000] ---[ end trace 00c8ee81ab80820a ]---
[ 18.627000] input: dreambox remote control (native) as /devices/virtual/input/input0
[ 18.629000] input: dreambox advanced remote control (native) as /devices/virtual/input/input1
[ 18.635000] input: dreambox ir keyboard as /devices/virtual/input/input2
[ 18.637000] input: dreambox ir mouse as /devices/virtual/input/input3
Configuring network interfaces... [ 21.954000] bcmemac: eth0 NIC Link is Down
udhcpc (v1.19.4) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Starting tpmd.
INIT: Entering runlevel: 3
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting automounter: loading autofs4 kernel module, done.
Starting dbttcd.
Starting syslogd/klogd: done
Starting internet superserver: xinetd.
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
/dev/dvb/adapter0/video0: No such file or directory
enigma2 is the main pvr application... adjust oom score!
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
setIoPrio best-effort level 7 ok
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
setIoPrio best-effort level 7 ok
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
enigma2 is the main pvr application... adjust oom score!
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
enigma2 is the main pvr application... adjust oom score!
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
setIoPrio best-effort level 7 ok
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
enigma2 is the main pvr application... adjust oom score!
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
setIoPrio best-effort level 7 ok
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
enigma2 is the main pvr application... adjust oom score!
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
setIoPrio best-effort level 7 ok
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
enigma2 is the main pvr application... adjust oom score!
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
setIoPrio best-effort level 7 ok
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
enigma2 is the main pvr application... adjust oom score!
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
enigma2 is the main pvr application... adjust oom score!
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
/dev/dvb/adapter0/video0: No such file or directory
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
realpath /etc/enigma2/settings: No such file or directory
[eTPM] connect error
Enigma2 v4.0.0 (revision: tarball-20130114-0-g9dd0312, date: 2013-01-14)
Enigma2 is property of Dream Multimedia GmbH. All copyrights with regard to
Enigma2 belong to Dream Multimedia GmbH only.
The full license text is available at /usr/share/doc/enigma2/LICENSE.
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
before: 1
after: 1
+ (8) graphics acceleration manager
setIoPrio best-effort level 7 ok
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Aborted
INIT: Id "e2" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
enigma2 is the main pvr application... adjust oom score!
/usr/bin/enigma2.sh: line 43: can't create /proc//oom_adj: nonexistent directory
libpagecache exists... drop caches now!
libpagecache exists... drop caches now!
libpagecache exists... drop caches now!
libpagecache exists... drop caches now!
