[Paskalito]

0

Hello everyone...
like i said im very sorry for ask again this problem...
i have read a lot about this problem and i really cant fix it...
i have a dm800se with ssl82 and i put a ssl84 image so i brick it..
The box said "err no ca found"...but i try every solution optiflash...repair tool
and no result....i think my box is dead i flash again with browser and with optiflash but nothing....i reboot and the error still here...it is possible to fix it or the box can be really dead(bricked, blocked)
i dont no if you can help me i appriciate a lot

i put out the sim clean it and still no result...

sorry again for make another thread about this but im really lost thanks...

[fairbird]

0

You box Genuine or Clone ?

[Paskalito]

0

You box Genuine or Clone ?

Its a clone...

[duli]

0

hi mate I had the same problem and it was nearly to use my box for parts after i had to do the final thing:
This is what i did
You had to have 2 dm800 one that is working and the other one that does not communicate with your RS232, DreamUp pacht, putty, hyperterminal, Optiflasher or anything.

All you have to do is:
1. connect the working DM800 with dreamUp1339
2. Let the dreamUp to find the working Dm800 and to upload flash loader
3. after this remove the power and the RS232 from the working dreambox without disconnecting the dreamup
4. connect the RS232, Lan and Power to your dreambox
5. brows from flash button in the dreamUP for a NAND image and look to your dreambox that it has been given an IP
6. put your IP in your brouser and chose a Image for me it works this
(Nemesis2.4 patched by voyger sim2.0.1-dm800-e2-OE(1.6)-SVN(101r1))
hope this helps you MATE it worked for me

Regards

[Paskalito]

0

hi mate I had the same problem and it was nearly to use my box for parts after i had to do the final thing:
This is what i did
You had to have 2 dm800 one that is working and the other one that does not communicate with your RS232, DreamUp pacht, putty, hyperterminal, Optiflasher or anything.

All you have to do is:
1. connect the working DM800 with dreamUp1339
2. Let the dreamUp to find the working Dm800 and to upload flash loader
3. after this remove the power and the RS232 from the working dreambox without disconnecting the dreamup
4. connect the RS232, Lan and Power to your dreambox
5. brows from flash button in the dreamUP for a NAND image and look to your dreambox that it has been given an IP
6. put your IP in your brouser and chose a Image for me it works this
(Nemesis2.4 patched by voyger sim2.0.1-dm800-e2-OE(1.6)-SVN(101r1))
hope this helps you MATE it worked for me

Regards

Hello my friend thanks a lot for your help thank you relly mucho...



but i have tryed and tryed and tryed your method... and no way....

i put my working dm800...with dreamup patched or the 1339 Vers.
and when i do that my working box the screen put no ca found error lol...
but when i plug it whitout dreamup its working great...
but with dreamup 1339 no flash buton appears its still grey...
with patched dreamup the flash button appears and when i put the bad box(dm800 dead) no ip...only no ca found error blablabla...

so...i dont know what to do...i think its really dead but i hope not...
i got a dm800 clone ssl84 like this and a dm800se 82 like this....same sh#t

i really dont understand and dont think im a beginner on this box's i use a lot and i work a lot with those' but this time....im speackless...sorry again for disturb asking for solution...and thanks again for your kind help
salut'my friend

really desesperate...i gonna put it in garbage i think lol....
take care

---

thanks for your great site yassinov i send you only 10 but its a start and firstable for be thankfull' for all you make here for us take car bless ;)